C.F.R. homeSearch C.F.R.
C.F.R.Title 49Chapter II—Federal Railroad Administration, Department of TransportationPart 213—Track Safety StandardsSubpart G—Train Operations at Track Classes 6 and Higher

49 C.F.R. § 213.331 (2026)

Track surface

Edition and currency
eCFR text as of Sept. 29, 2026. The text is the edition Syfert holds; for a past event, check the version in force on that date.
Other sources
CURRENTeCFR text as of Sept. 29, 2026

(a) For a single deviation in track surface, each track owner shall maintain the surface of its track within the limits prescribed in the following table:

Track surface (inches)Class of track
6789
The deviation from uniform 1 profile on either rail at the mid-ordinate of a 31-foot chord may not be more than113⁄41⁄2
The deviation from uniform profile on either rail at the mid-ordinate of a 62-foot chord may not be more than1113⁄4
Except as provided in paragraph (b) of this section, the deviation from uniform profile on either rail at the mid-ordinate of a 124-foot chord may not be more than13⁄411⁄211⁄41
The deviation from zero crosslevel at any point on tangent track may not be more than 21111
Reverse elevation on curves may not be more than1⁄21⁄21⁄21⁄2
The difference in crosslevel between any two points less than 62 feet apart may not be more than 311⁄211⁄211⁄41
On curved track, the difference in crosslevel between any two points less than 10 feet apart (short warp) may not be more than11⁄411⁄813⁄4
1 Uniformity for profile is established by placing the midpoint of the specified chord at the point of maximum measurement.
2 If physical conditions do not permit a spiral long enough to accommodate the minimum length of runoff, part of the runoff may be on tangent track.
3 However, to control harmonics on jointed track with staggered joints, the crosslevel differences shall not exceed 1 inch in all of six consecutive pairs of joints, as created by seven low joints. Track with joints staggered less than 10 feet apart shall not be considered as having staggered joints. Joints within the seven low joints outside of the regular joint spacing shall not be considered as joints for purposes of this footnote.

(b) For operations at a qualified cant deficiency, Eu, of more than 5 inches, a single deviation in track surface shall be within the limits prescribed in the following table:

Track surface (inches)Class of track
6789
The difference in crosslevel between any two points less than 10 feet apart (short warp) may not be more than11⁄41113⁄4
The deviation from uniform profile on either rail at the mid-ordinate of a 124-foot chord may not be more than11⁄211⁄411⁄41
1 For curves with a qualified cant deficiency, Eu, of more than 7 inches, the difference in crosslevel between any two points less than 10 feet apart (short warp) may not be more than three-quarters of an inch.

(c) For three or more non-overlapping deviations in track surface occurring within a distance equal to five times the specified chord length, each of which exceeds the limits in the following table, each track owner shall maintain the surface of the track within the limits prescribed for each deviation:

Track surface (inches)Class of track
6789
The deviation from uniform profile on either rail at the mid-ordinate of a 31-foot chord may not be more than3⁄43⁄41⁄23⁄8
The deviation from uniform profile on either rail at the mid-ordinate of a 62-foot chord may not be more than3⁄43⁄43⁄41⁄2
The deviation from uniform profile on either rail at the mid-ordinate of a 124-foot chord may not be more than11⁄417⁄85⁄8
[78 FR 16106, Mar. 13, 2013]
Enactment and amendments

Syfert holds no separate history line for this section. Where this code prints a source or history note, it appears with the text, usually at the end.

Versions

Edition shown: eCFR text as of Sept. 29, 2026. Syfert holds no earlier or later version of this section.

C.F.R. Home  |  Search C.F.R.  |  Search cases for this section  |  syfert.com