C.F.R. homeSearch C.F.R.
C.F.R.Title 49Chapter II—Federal Railroad Administration, Department of TransportationPart 213—Track Safety StandardsSubpart D—Track Structure

49 C.F.R. § 213.109 (2026)

Crossties

Edition and currency
eCFR text as of Sept. 29, 2026. The text is the edition Syfert holds; for a past event, check the version in force on that date.
Other sources
CURRENTeCFR text as of Sept. 29, 2026 cited 2000–2019 4citing cases
At a glance

Courts have cited this section in 4 opinions since 2000.

(a) Crossties shall be made of a material to which rail can be securely fastened.

(b) Each 39-foot segment of track shall have at a minimum—

(1) A sufficient number of crossties that in combination provide effective support that will—

(i) Hold gage within the limits prescribed in § 213.53(b);

(ii) Maintain surface within the limits prescribed in § 213.63; and

(iii) Maintain alinement within the limits prescribed in § 213.55;

(2) The minimum number and type of crossties specified in paragraph (b)(4) of this section and described in paragraph (c) or (d), as applicable, of this section effectively distributed to support the entire segment;

(3) At least one non-defective crosstie of the type specified in paragraphs (c) and (d) of this section that is located at a joint location as specified in paragraph (e) of this section; and

(4) The minimum number of crossties as indicated in the following table.

FRA track classTangent track, turnouts, and curves
Tangent track and curved track less than or equal to 2 degreesTurnouts and curved track greater than 2 degrees
Class 156
Class 289
Class 3810
Class 4 and 51214

(c) Crossties, other than concrete, counted to satisfy the requirements set forth in paragraph (b)(4) of this section shall not be—

(1) Broken through;

(2) Split or otherwise impaired to the extent the crosstie will allow the ballast to work through, or will not hold spikes or rail fasteners;

(3) So deteriorated that the crosstie plate or base of rail can move laterally 1/2 inch relative to the crosstie; or

(4) Cut by the crosstie plate through more than 40 percent of a crosstie's thickness.

(d) Concrete crossties counted to satisfy the requirements set forth in paragraph (b)(4) of this section shall not be—

(1) Broken through or deteriorated to the extent that prestressing material is visible;

(2) Deteriorated or broken off in the vicinity of the shoulder or insert so that the fastener assembly can either pull out or move laterally more than 3/8 inch relative to the crosstie;

(3) Deteriorated such that the base of either rail can move laterally more than 3/8 inch relative to the crosstie on curves of 2 degrees or greater; or can move laterally more than 1/2 inch relative to the crosstie on tangent track or curves of less than 2 degrees;

(4) Deteriorated or abraded at any point under the rail seat to a depth of 1/2 inch or more;

(5) Deteriorated such that the crosstie's fastening or anchoring system, including rail anchors (see § 213.127(b)), is unable to maintain longitudinal rail restraint, or maintain rail hold down, or maintain gage due to insufficient fastener toeload; or

(6) Configured with less than two fasteners on the same rail except as provided in § 213.127(c).

(e) Class 1 and 2 track shall have one crosstie whose centerline is within 24 inches of each rail joint (end) location. Class 3, 4, and 5 track shall have either one crosstie whose centerline is within 18 inches of each rail joint location or two crossties whose centerlines are within 24 inches either side of each rail joint location. The relative position of these crossties is described in the following three diagrams:

(1) Each rail joint in Class 1 and 2 track shall be supported by at least one crosstie specified in paragraphs (c) and (d) of this section whose centerline is within 48 inches as shown in Figure 1.

(2) Each rail joint in Class 3, 4, and 5 track shall be supported by either at least one crosstie specified in paragraphs (c) and (d) of this section whose centerline is within 36 inches as shown in Figure 2, or:

(3) Two crossties, one on each side of the rail joint, whose centerlines are within 24 inches of the rail joint location as shown in Figure 3.

(f) For track constructed without crossties, such as slab track, track connected directly to bridge structural components, track over servicing pits, etc., the track structure shall meet the requirements of paragraph (b)(1) of this section.

[76 FR 18084, Apr. 1, 2011]
The 4 cases that cite 49 C.F.R. § 213.109 most heavily, weighted by court and treatment. RelevanceNewestTreatment
1
GREENKevin Cowden v. BNSF Ry. Co., 690 F.3d 884 (8th Cir. 2012).
cites § 213.109 1×cited by 58 cases
Where it cites § 213.109
“63 (regulating track surface conditions for each class of track); 49 C.F.R. § 213.109 (regulating number of sufficient crossties for each class of track); 49 C.”
The case’s holding
A defendant bears the burden of proving that specific federal regulations substantially subsume a negligence claim to establish preemption under the Federal Railroad Safety Act.
Later courts cite it for
“it is not clear how negligence claims brought under the federal common law threaten the uniformity sought by the frsa.” · 3 citing courts
2
GREENMurphy v. Town of Darien, 210 A.3d 56 (Conn. 2019).
cites § 213.109 2×cited by 4 cases
Where it cites § 213.109
“57 (2012) (establishing speed limitations based on curvature and elevation of track); 49 C.F.R. § 213.109 (2012) (establishing requirements for crossties); 49 C.”
3
GREENCowden v. BNSF Ry. Co., 975 F. Supp. 2d 1005 (E.D. Mo. 2013).
cites § 213.109 1×cited by 11 cases
Where it cites § 213.109
“In support of this, Defendant states, 49 C.F.R. § 213.109 (b) requires that ‘each 39 foot segment of track shall have (1) a sufficient number of crossties which in combination provide effective support that will .”
Later courts cite it for
“although 213.103 provides the applicable standard of care, genuine disputes of material fact remain as to whether defendant provided adequate ballast to properly support the track at issue.” · 2 citing courts
4
REDUnion Pac. R.R. v. California Pub. Utils. Comm'n, 109 F. Supp. 2d 1186 (N.D. Cal. 2000).
cites § 213.109 1×cited by 3 cases
Reversed in part by Union Pacific Railroad Company, Southern Pacific Transportation Company, Burlington Northern and Santa Fe Railway Company, and Brotherhood of Locomotive Engineers, United Transportation Union, Intervenors v. C…
Where it cites § 213.109
“33,992, 34,006; see also 49 C.F.R. § 213.109 . In its response to DOT’s brief, defendants also concede “that track standards are ‘covered’ by FRA rules.”
Later courts cite it for
“exhibited a combination of peculiar or distinctive features or characteristics (including environmental or demographic features) that are neither typical nor common or otherwise 'state-wide' in nature, and which create a safety hazard.” · 2 citing courts

The flag is Syfertize’s treatment of the citing case itself, not of the statute. “Where it cites” is the passage in the opinion; the holding is a summary of the whole case and may concern another point. Annotations are extracted automatically from the opinions in the Syfert caselaw corpus.

Citing cases by year
200020092019

One bar per year. Tallest: 1 case in 2000. These are opinions in the Syfert collection, which holds more of some courts’ recent opinions than their older ones, so a rise can reflect what the collection holds and not more litigation.

By court
8th Cir.1N.D. Cal.1Conn.1E.D. Mo.1
By subsection

Courts have not cited this section by subsection, so its cases are not split up here. The Leading cases tab lists the cases that cite it most heavily.

Enactment and amendments

Syfert holds no separate history line for this section. Where this code prints a source or history note, it appears with the text, usually at the end.

Versions

Edition shown: eCFR text as of Sept. 29, 2026. Syfert holds no earlier or later version of this section.

C.F.R. Home  |  Search C.F.R.  |  Search cases for this section  |  syfert.com